Drilling, reaming, boring, honing, and pulling hole processing technology


Release time:

2020-11-30

【Summary】Compared to the machining of outer cylindrical surfaces, the conditions for hole machining are significantly worse, making it more challenging than machining outer cylinders. This is due to several reasons: 1) The size of the tools used for hole machining is constrained by the size of the holes being machined, leading to poor rigidity, which can easily result in bending deformation and vibration; 2) When using fixed-size tools for hole machining, the size of the holes often directly depends on the corresponding size of the tools, and the manufacturing errors and wear of the tools will directly impact the machining accuracy of the holes; 3) During hole machining, the cutting area is located inside the workpiece, and the conditions for chip removal and cooling are poor, making it difficult to control machining accuracy and surface quality. I. Drilling and Reaming: 1. Drilling Drilling is the initial process of creating holes in solid materials, with the diameter of drilled holes typically being less than 80mm. There are two methods for drilling: one involves the rotation of the drill bit, while the other involves the rotation of the workpiece. The errors produced by these two drilling methods differ. In the method where the drill bit rotates, the asymmetry of the cutting edge and insufficient rigidity of the drill bit can cause the centerline of the machined hole to skew or become misaligned, although the hole diameter remains largely unchanged; conversely, in the method where the workpiece rotates, the deflection of the drill bit can lead to changes in the hole diameter while the centerline of the hole remains straight. Commonly used drilling tools include twist drills, center drills, and deep hole drills, with twist drills being the most frequently used, having a diameter specification of Φ0.1-80mm. Due to structural limitations, both the bending rigidity and torsional rigidity of the drill bit are low, combined with poor centering, resulting in relatively low drilling accuracy, typically only achieving IT13~IT11; the surface roughness is also relatively high, generally Ra being 50~12.5μm; however, drilling has a high metal removal rate and cutting efficiency. Drilling is primarily used for machining holes with low quality requirements, such as bolt holes, threaded bottom holes, and oil holes. For holes requiring higher machining accuracy and surface quality, subsequent processes such as reaming, honing, boring, or grinding should be employed to achieve the desired results. 2. Reaming Reaming is a further machining process that uses a reamer on holes that have already been drilled, cast, or forged to enlarge the hole diameter and enhance the machining quality of the hole. Reaming can serve as a pre-processing step before finishing holes or as the final processing for holes with lower requirements. Reamers are similar to twist drills but have more cutting edges and lack side cutting edges. Compared to drilling, reaming has the following characteristics: (1) Reamers have more cutting edges (3~8 edges), good guidance, and stable cutting; (2) Reamers do not have side cutting edges, providing favorable cutting conditions; (3) The machining allowance is relatively small, allowing for shallower chip flutes and thicker drill cores, resulting in better tool strength and rigidity. The accuracy of reaming is generally at the IT11~IT10 level, and the surface roughness Ra is 12.5~6.3μm. Reaming is commonly used for machining holes with diameters less than a certain size. When drilling larger diameter holes (D ≥30mm), it is common to first pre-drill with a small drill bit (with a diameter of 0.5~0.7 times the hole diameter) and then use a corresponding size reamer to enlarge the hole, which can improve the machining quality and production efficiency of the hole. In addition to machining cylindrical holes, reaming can also utilize various specially shaped reamers (also known as counterbore drills) to process various counterbored holes and flat end surfaces. The front end of the counterbore drill often features a guiding column to assist in guiding the already machined hole. II. Honing Honing is one of the precision machining methods for holes and is widely applied in production. For smaller holes, honing is a more economical and practical machining method compared to internal cylindrical grinding and precision boring. 1. Honing Tool Honing tools are generally categorized into hand honing tools and machine honing tools. Hand honing tools have a straight handle, a longer working part, and good guiding action. Hand honing tools come in two structures: integral and adjustable outer diameter. Machine honing tools are available in two structures: with a handle and sleeve type. Honing tools can process not only round holes but also conical holes using conical honing tools. 2. Honing Process and Its Applications The allowance for honing significantly impacts honing quality. If the allowance is too large, the load on the honing tool increases, causing the cutting edges to dull quickly, making it difficult to achieve a smooth machined surface, and dimensional tolerances become hard to guarantee; if the allowance is too small, it cannot remove the tool marks left by the previous process, thus failing to improve the quality of hole machining. Generally, the rough honing allowance is set at 0.35~0.15mm, and the fine honing allowance is set at 0.15~0.05mm. To prevent the formation of built-up edge, honing typically employs a lower cutting speed (for high-speed steel honing tools machining steel and cast iron, v <8m/min). The feed rate is related to the diameter of the hole being machined; the larger the hole diameter, the larger the feed rate. For high-speed steel honing tools machining steel and cast iron, the feed rate is often set at 0.3~1mm/r. During honing, it is essential to use appropriate cutting fluid for cooling, lubrication, and cleaning to prevent built-up edge formation and to remove chips in a timely manner. Compared to grinding and boring, honing has higher productivity and is easier to ensure hole accuracy; however, honing cannot correct positional errors of the hole axis, and the positional accuracy of the hole should be guaranteed by the previous process. Honing is not suitable for processing stepped holes and blind holes. The dimensional accuracy of honing is generally at the IT9~IT7 level, and the surface roughness Ra is generally 3.2~0.8 μm. For medium-sized holes with high precision requirements (such as IT7 level precision holes), the drilling-reaming-honing process is a commonly used typical machining scheme in production. III. Boring Boring is a machining method that uses cutting tools to enlarge pre-formed holes. Boring can be performed on a boring machine or a lathe. 1. Boring Methods: There are three different machining methods for boring. (1) Workpiece rotation, tool feeding motion. Most boring on a lathe belongs to this boring method. The process characteristics are: the axis of the machined hole is consistent with the workpiece's rotation axis after machining, the roundness of the hole mainly depends on the rotational accuracy of the machine spindle, and the axial geometric shape error of the hole mainly depends on the positional accuracy of the tool feeding direction relative to the workpiece's rotation axis. This boring method is suitable for machining holes that require coaxiality with the outer cylindrical surface. (2) Tool rotation, workpiece feeding motion. The spindle of the boring machine drives the boring tool to rotate, while the worktable drives the workpiece to feed. (3) Tool rotation and feeding motion. In this boring method, the extension length of the boring bar varies, and the force deformation of the boring bar also changes. The hole diameter near the spindle box is larger, while the hole diameter farther from the spindle box is smaller, forming a conical hole. Additionally, as the extension length of the boring bar increases, the bending deformation of the spindle due to its weight also increases, causing the axis of the machined hole to bend accordingly. This boring method is only suitable for machining shorter holes. 2. Diamond Boring Compared to general boring, diamond boring is characterized by a small back cutting amount, small feed rate, and high cutting speed, allowing for very high machining accuracy (IT7~IT6) and very smooth surfaces (Ra of 0.4~0.05 μm). Diamond boring was initially performed using diamond boring tools, but now hard alloys, CBN, and synthetic diamond tools are commonly used. It is mainly used for machining non-ferrous metal workpieces, but can also be used for machining cast iron and steel parts. Common cutting amounts for diamond boring are: back cutting amount for pre-boring is 0.2~0.6mm, for final boring is 0.1mm; feed rate is 0.01~0.14mm/r; cutting speed when machining cast iron is 100~250m/min, when machining steel is 150~300m/min, and when machining non-ferrous metals is 300~2000m/min. To ensure that diamond boring achieves high machining accuracy and surface quality, the machine tool (diamond boring machine) must have high geometric accuracy and rigidity, and the spindle bearings are often precision angular contact ball bearings or hydrostatic sliding bearings. High-speed rotating parts must be precisely balanced; in addition, the movement of the feeding mechanism must be very smooth to ensure that the worktable can perform stable low-speed feeding motion. Diamond boring has good machining quality and high production efficiency, and is widely used for the final machining of precision holes in mass production, such as engine cylinder holes, piston pin holes, and spindle holes on machine tool spindle boxes. However, it should be noted that when machining ferrous metal products with diamond boring, only boring tools made of hard alloys and CBN can be used, and diamond tools cannot be used, as the carbon atoms in diamond have a strong affinity for iron group elements, leading to low tool life. 3. Boring Tool Boring tools can be divided into single-edged and double-edged boring tools. 4. Process Characteristics and Application Range of Boring Compared to the drilling-reaming-honing process, the diameter size of boring is not limited by the tool size, and boring has strong error correction capabilities, allowing for the correction of original hole axis skew errors through multiple passes, and can maintain high positional accuracy of the bored hole relative to the reference surface. Compared to turning the outer cylinder, due to the poor rigidity of the tool rod system, large deformation, and poor heat dissipation and chip removal conditions, the thermal deformation of the workpiece and tool is relatively large, resulting in lower machining quality and production efficiency for boring than for turning the outer cylinder. From the above analysis, it can be seen that boring has a wide machining range and can process various holes of different sizes and precision levels. For larger diameter holes with high dimensional and positional accuracy requirements, boring is almost the only machining method. The machining accuracy of boring is at the IT9~IT7 level. Boring can be performed on boring machines, lathes, milling machines, etc., and has the advantage of being flexible and mobile, making it widely used in production. In mass production, to improve boring efficiency, boring jigs are often used. IV. Honing Holes 1. Honing Principle and Honing Head Honing is a method of finishing holes using a honing head equipped with abrasive strips (oil stones). During honing, the workpiece is fixed, and the honing head is driven by the machine spindle to rotate and perform reciprocating linear motion. During honing, the abrasive strips exert a certain pressure on the workpiece surface, removing a very thin layer of material from the workpiece surface, with a cutting trajectory that is a crossed mesh pattern. To ensure that the movement trajectory of the abrasive particles does not repeat, the revolutions per minute of the honing head's rotation should be coprime with the number of reciprocating strokes per minute of the honing head. To facilitate the discharge of broken abrasive particles and chips, reduce cutting temperature, and improve machining quality, sufficient cutting fluid should be used during honing. To ensure uniform machining of the walls of the processed hole, the stroke of the abrasive strips should exceed a certain amount at both ends of the hole. To ensure uniform honing allowance and reduce the impact of spindle rotation errors on machining accuracy, a floating connection is often used between the honing head and the machine spindle. The radial adjustment of the honing head's abrasive strips can have various structural forms, including manual, pneumatic, and hydraulic. 2. Process Characteristics and Application Range of Honing 1) Honing can achieve high dimensional and shape accuracy, with machining accuracy at the IT7~IT6 level, and the roundness and cylindricity errors of the hole can be controlled within a certain range, but honing cannot improve the positional accuracy of the processed hole. 2) Honing can achieve high surface quality, with surface roughness Ra of 0.2~0.25μm, and the depth of the altered defect layer of the surface metal is very small, ranging from 2.5~25μm. 3) Compared to grinding speed, the circumferential speed of the honing head is not high (vc=16~60m/min), but due to the large contact area between the abrasive strips and the workpiece, the reciprocating speed is relatively high (va=8~20m/min), so honing still has a high productivity. Honing is widely used in mass production for the machining of precision holes in engine cylinder holes and various hydraulic devices, with a hole diameter range generally being or larger, and can process deep holes with a length-to-diameter ratio greater than 10. However, honing is not suitable for processing holes in non-ferrous metal workpieces with high plasticity, nor can it process holes with keyways, spline holes, etc. V. Pulling Holes 1. Pulling and Pulling Tool Pulling holes is a high productivity finishing method that is performed using a special pulling tool on a pulling machine. Pulling machines are divided into horizontal and vertical types, with horizontal pulling machines being the most common. During pulling, the pulling tool only performs low-speed linear motion (main motion). The number of working teeth of the pulling tool should generally not be less than 3; otherwise, the pulling tool will not work smoothly, easily producing circular ripples on the workpiece surface. To avoid excessive pulling force that could break the pulling tool, the number of working teeth of the pulling tool should generally not exceed 6~8. There are three different pulling methods, described as follows: 1) Layered Pulling. This pulling method is characterized by the pulling tool removing the machining allowance of the workpiece layer by layer in sequence. To facilitate chip breaking, the cutting edges are ground with interleaved chip flutes. A pulling tool designed for layered pulling is called a standard pulling tool. 2) Block Pulling. This pulling method is characterized by each layer of metal on the machined surface being removed by a group of cutting edges that are basically the same size but interleaved (usually each group consists of 2-3 cutting edges). Each cutting edge only removes a portion of the metal layer. A pulling tool designed for block pulling is called a wheel-cutting pulling tool. 3) Comprehensive Pulling. This method combines the advantages of layered and block pulling, with the rough cutting edges using block pulling and the fine cutting edges using layered pulling. This not only shortens the length of the pulling tool and improves productivity but also achieves better surface quality. A pulling tool designed for comprehensive pulling is called a comprehensive pulling tool. 2. Process Characteristics and Application Range of Pulling Holes 1) Pulling tools are multi-edged tools that can sequentially complete rough machining, fine machining, and finishing work of holes in one pulling stroke, resulting in high production efficiency. 2) The accuracy of pulling holes mainly depends on the accuracy of the pulling tool. Under normal conditions, the accuracy of pulling holes can reach IT9~IT7, and the surface roughness Ra can reach 6.3~1.6 μm. 3) During pulling, the workpiece is positioned by the hole itself (the leading part of the pulling tool serves as the positioning element of the workpiece), making it difficult to ensure the mutual positional accuracy of the hole with other surfaces; for rotating parts that require coaxiality between inner and outer cylindrical surfaces, the hole is often pulled first, and then other surfaces are machined based on the hole as the positioning reference. 4) Pulling tools can process not only round holes but also shaped holes and spline holes. 5) Pulling tools are fixed-size tools, complex in shape, and expensive, making them unsuitable for machining large holes. Pulling holes are commonly used in mass production for processing through holes with diameters of Ф10~80mm and depths not exceeding 5 times the diameter.

                                                     Drilling, reaming, boring, and hole pulling processing technology

Compared with the processing of outer circular surfaces, the conditions for hole processing are much worse, and processing holes is more difficult than processing outer circles. This is because:

1) The size of the tools used for hole processing is limited by the size of the processed hole, which has poor rigidity and is prone to bending deformation and vibration;

2) When processing holes with fixed-size tools, the size of the processed hole often directly depends on the corresponding size of the tool, and the manufacturing errors and wear of the tool will directly affect the processing accuracy of the hole;

3) During hole processing, the cutting area is inside the workpiece, and the chip removal and heat dissipation conditions are poor, making it difficult to control processing accuracy and surface quality.

I. Drilling and reaming: 1. Drilling

Drilling is the first process of creating holes in solid materials, with the diameter of the holes generally being less than 80mm. There are two methods for drilling: one involves the rotation of the drill bit, while the other involves the rotation of the workpiece. The errors produced by these two methods differ. In the method where the drill bit rotates, the centerline of the hole may deviate or become misaligned due to the asymmetry of the cutting edge and insufficient rigidity of the drill bit, although the hole diameter remains largely unchanged. Conversely, in the workpiece rotation method, deviation of the drill bit leads to changes in hole diameter, while the centerline remains straight. Common drilling tools include twist drills, center drills, and deep hole drills, with twist drills being the most commonly used, having a diameter specification of Φ0.1-80mm.

Due to structural limitations, both the bending rigidity and torsional rigidity of the drill bit are low, combined with poor centering, resulting in relatively low drilling accuracy, typically only achieving IT13 to IT11. The surface roughness is also relatively high, generally Ra being 50 to 12.5μm. However, drilling has a high metal removal rate and cutting efficiency. It is mainly used for processing holes with low quality requirements, such as bolt holes, thread bottom holes, and oil holes. For holes requiring higher processing accuracy and surface quality, subsequent processes such as reaming, boring, or grinding should be employed.

2. Reaming

Reaming is a further processing of holes that have already been drilled, cast, or forged using a reamer to enlarge the hole diameter and improve the processing quality of the hole. Reaming can serve as a pre-processing step before finishing holes or as the final processing for holes with lower requirements. Reamers are similar to twist drills but have more cutting edges and no side cutting edges.

Compared to drilling, reaming has the following characteristics: (1) Reamers have more cutting edges (3 to 8 edges), good guidance, and stable cutting; (2) Reamers lack side cutting edges, which provides favorable cutting conditions; (3) The processing allowance is smaller, allowing for shallower chip flutes, thicker drill cores, and better strength and rigidity of the tool body. The accuracy of reaming is generally at the IT11 to IT10 level, with a surface roughness Ra of 12.5 to 6.3μm. Reaming is commonly used for processing holes with diameters less than a certain size. When drilling larger diameter holes (D ≥30mm), it is common to first pre-drill with a small drill bit (with a diameter of 0.5 to 0.7 times the hole diameter) and then use a reamer of the corresponding size to enlarge the hole, which can enhance processing quality and production efficiency.

In addition to processing cylindrical holes, reaming can also use various specially shaped reamers (also known as counterbore drills) to process various counterbored holes and counterbored flat end faces. The front end of the counterbore drill often has a guide post for guiding through the processed hole.

 

II. Boring

Boring is one of the precision machining methods for holes and is widely used in production. For smaller holes, boring is a more economical and practical processing method compared to internal cylindrical grinding and precision boring.

1. Boring Tool

Boring tools are generally divided into hand boring tools and machine boring tools. Hand boring tools have a straight handle, a longer working part, and good guiding action. Hand boring tools come in two structures: integral and adjustable outer diameter. Machine boring tools come in two structures: with a handle and sleeve type. Boring tools can process not only round holes but also conical holes using conical boring tools.

2. Boring Process and Its Applications

The allowance for boring has a significant impact on the quality of the boring process. If the allowance is too large, the load on the boring tool is high, the cutting edge quickly becomes dull, making it difficult to obtain a smooth processing surface, and the dimensional tolerance is also hard to guarantee; if the allowance is too small, it cannot remove the tool marks left by the previous process, thus failing to improve the quality of hole processing. Generally, the rough boring allowance is taken as 0.35~0.15mm, and the fine boring allowance is taken as 01.5~0.05mm.

To avoid the formation of built-up edge, boring usually adopts a lower cutting speed (for high-speed steel boring tools processing steel and cast iron, v <8m/min). The feed rate is related to the diameter of the processed hole; the larger the hole diameter, the larger the feed rate. For high-speed steel boring tools processing steel and cast iron, the feed rate is often taken as 0.3~1mm/r.

During boring, it is essential to use appropriate cutting fluid for cooling, lubrication, and cleaning to prevent the formation of built-up edge and to remove chips in a timely manner. Compared with grinding and boring, the productivity of boring is high, and it is easy to ensure the accuracy of the hole; however, boring cannot correct the positional error of the hole axis, and the positional accuracy of the hole should be guaranteed by the previous process. Boring is not suitable for processing stepped holes and blind holes.

The dimensional accuracy of boring is generally at the IT9 to IT7 level, and the surface roughness Ra is typically between 3.2 to 0.8 μm. For medium-sized holes with high precision requirements (such as IT7 level precision holes), the drilling-reaming-boring process is a commonly used typical processing scheme in production.

III. Boring

Boring is a processing method that uses cutting tools to enlarge pre-formed holes, and boring work can be performed on a boring machine or a lathe.

1. Boring Methods: There are three different processing methods for boring.

(1) The workpiece rotates, and the tool feeds. Most boring on a lathe belongs to this boring method. The process characteristics are: the axis of the processed hole is consistent with the rotation axis of the workpiece, the roundness of the hole mainly depends on the rotation accuracy of the machine spindle, and the axial geometric shape error of the hole mainly depends on the positional accuracy of the tool feed direction relative to the rotation axis of the workpiece. This boring method is suitable for processing holes that require coaxiality with the outer circular surface.

(2) The tool rotates, and the workpiece feeds. The spindle of the boring machine drives the boring tool to rotate, and the worktable drives the workpiece to feed.

(3) The tool rotates and feeds. In this boring method, the extension length of the boring bar varies, and the deformation of the boring bar under load also changes. The diameter of the hole near the spindle box is larger, while the diameter of the hole farther from the spindle box is smaller, forming a conical hole. In addition, as the extension length of the boring bar increases, the bending deformation caused by the weight of the spindle also increases, resulting in corresponding bending of the axis of the processed hole. This boring method is only suitable for processing shorter holes.

2. Diamond Boring

Compared to conventional boring, diamond boring is characterized by a small back cutting amount, low feed rate, and high cutting speed. It can achieve very high machining accuracy (IT7 to IT6) and a very smooth surface finish (Ra of 0.4 to 0.05 μm). Initially, diamond boring was performed using diamond boring tools, but now hard alloys, CBN, and synthetic diamond tools are commonly employed. It is primarily used for machining non-ferrous metal workpieces, but can also be applied to cast iron and steel components.

The commonly used cutting parameters for diamond boring are: back cutting amount for rough boring is 0.2~0.6mm, for finish boring is 0.1mm; feed amount is 0.01~0.14mm/r; cutting speed when processing cast iron is 100~250m/min, when processing steel is 150~300m/min, and when processing non-ferrous metals is 300~2000m/min.

To ensure that diamond boring can achieve high processing accuracy and surface quality, the machine tool (diamond boring machine) must have high geometric accuracy and rigidity. The spindle bearings of the machine tool commonly use precision angular contact ball bearings or hydrostatic sliding bearings, and high-speed rotating parts must be precisely balanced. In addition, the motion of the feeding mechanism must be very smooth to ensure that the worktable can perform stable low-speed feeding.

Diamond boring has good processing quality and high production efficiency, and is widely used in the final processing of precision holes in mass production, such as engine cylinder holes, piston pin holes, and spindle holes on machine tool spindle boxes. However, it should be noted that when processing ferrous metal products with diamond boring, only boring tools made of hard alloys and CBN can be used, and diamond boring tools cannot be used because the carbon atoms in diamond have a strong affinity for iron group elements, resulting in low tool life.

3. Boring Tool

Boring tools can be divided into single-edged boring tools and double-edged boring tools.

4. Process Characteristics and Application Range of Boring

Compared with drilling—reaming—boring processes, the diameter size is not limited by the tool size, and boring has a strong error correction capability. It can correct the original hole axis deviation error through multiple passes, and can maintain a high positional accuracy of the bored hole relative to the reference surface.

Compared with turning the outer circle, due to the poor rigidity of the tool rod system, large deformation, and poor heat dissipation and chip removal conditions, the thermal deformation of the workpiece and tool is relatively large, so the processing quality and production efficiency of boring are not as high as that of turning the outer circle.

From the above analysis, it can be seen that the processing range of boring is wide, capable of processing various holes of different sizes and precision levels. For holes with larger diameters and higher dimensional and positional accuracy requirements, boring is almost the only processing method. The processing accuracy of boring is IT9~IT7 level. Boring can be performed on boring machines, lathes, milling machines, etc., with the advantage of being flexible and mobile, and is widely used in production. In mass production, to improve boring efficiency, boring jigs are often used.

4. Honing Holes 1. Honing Principle and Honing Head

Honing is a method of finishing holes using a honing head equipped with abrasive strips (oil stones). During honing, the workpiece is fixed, and the honing head is driven by the machine tool spindle to rotate and perform reciprocating linear motion. In honing, the abrasive strips exert a certain pressure on the workpiece surface, removing a very thin layer of material from the workpiece surface, with a cutting trajectory that is a crossed mesh. To ensure that the movement trajectory of the abrasive particles does not repeat, the revolutions per minute of the honing head's rotary motion and the reciprocating stroke per minute should be coprime.

To facilitate the discharge of broken abrasive particles and chips, reduce cutting temperature, and improve processing quality, sufficient cutting fluid should be used during honing. To ensure that the walls of the processed hole receive uniform processing, the stroke of the abrasive strips should exceed a certain amount at both ends of the hole. To ensure uniform honing allowance and reduce the impact of spindle rotation errors on processing accuracy, a floating connection is mostly used between the honing head and the machine tool spindle.

The radial adjustment of the honing head's abrasive strips can be manual, pneumatic, or hydraulic in various structural forms.

2. Process Characteristics and Application Range of Honing

1) Honing can achieve high dimensional accuracy and shape accuracy, with processing accuracy of IT7~IT6 level, and the roundness and cylindricity errors of the hole can be controlled within a certain range, but honing cannot improve the positional accuracy of the processed hole.

2) Honing can achieve a high surface quality, with a surface roughness Ra of 0.2 to 0.25 μm, and the depth of the altered defect layer in the surface metal is very minimal, ranging from 2.5 to 25 μm.

3) Compared to grinding speed, although the circumferential speed of the honing head is not high (vc=16~60m/min), due to the large contact area between the abrasive strips and the workpiece, the reciprocating speed is relatively high (va=8~20m/min), so honing still has a high productivity.

Honing is widely used in mass production for the processing of precision holes in engine cylinder holes and various hydraulic devices, with a typical hole diameter range of or larger, and can process deep holes with a length-to-diameter ratio greater than 10. However, honing is not suitable for processing holes in non-ferrous metal workpieces with high plasticity, nor can it process holes with keyways, spline holes, etc.

5. Pulling Holes 1. Pulling and Pulling Tools

Pulling holes is a high productivity finishing method, performed using a special pulling tool on a pulling machine. Pulling machines are divided into horizontal and vertical types, with horizontal pulling machines being the most common.

During pulling, the puller only performs low-speed linear motion (main motion). The number of working teeth of the puller should generally not be less than 3; otherwise, the puller will not work smoothly, and it is easy to produce annular ripples on the workpiece surface. To avoid excessive pulling force that may cause the puller to break, the number of working teeth of the puller should generally not exceed 6 to 8.

There are three different pulling methods for hole pulling, described as follows:

1) Layered pulling: This method is characterized by the puller removing the machining allowance of the workpiece layer by layer in sequence. To facilitate chip breaking, the teeth are ground with interleaved chip grooves. The puller designed according to the layered pulling method is called a standard puller.

2) Block pulling: This method is characterized by each layer of metal on the machined surface being removed by a group of teeth that are basically the same size but interleaved (usually each group consists of 2-3 teeth). Each tooth only removes a part of a layer of metal. The puller designed according to the block pulling method is called a wheel-cut puller.

3) Comprehensive pulling: This method combines the advantages of layered and block pulling. The rough cutting teeth use block pulling, while the finishing teeth use layered pulling. This not only shortens the length of the puller and improves productivity but also achieves better surface quality. The puller designed according to the comprehensive pulling method is called a comprehensive puller.

2. Process characteristics and application range of hole pulling

1) The puller is a multi-edge tool that can sequentially complete rough machining, finishing, and polishing of the hole in one pulling stroke, resulting in high production efficiency.

2) The accuracy of reaming mainly depends on the precision of the reamer. Under normal conditions, the accuracy of reaming can reach IT9 to IT7, and the surface roughness Ra can reach 6.3 to 1.6 μm.

3) During hole pulling, the workpiece is positioned by the hole itself (the leading part of the puller is the positioning element of the workpiece), making it difficult to ensure the positional accuracy between the hole and other surfaces; for rotating parts that require coaxiality between inner and outer cylindrical surfaces, it is often the case that the hole is pulled first, and then other surfaces are machined based on the hole as the positioning reference.

4) The puller can process not only round holes but also shaped holes and spline holes.

5) The puller is a fixed-size tool, with a complex shape and high Price, making it unsuitable for processing large holes.

Hole pulling is commonly used in mass production for processing through holes with a diameter of Ф10 to 80 mm and a depth not exceeding five times the diameter.

TAG:


RELATED INFORMATION

ADD

Gengguantun Industrial Development Zone, Qingxian County, Hebei Province, China

WeChat applet

WeChat applet

Business License