CNC Turning Operator Skills


Release time:

2020-12-09

【Summary】Programming Skills 1. Processing Sequence of Parts: Drill holes first, then flatten the ends (this prevents material shrinkage during drilling); rough turning first, then finish turning (this ensures part accuracy); process larger tolerances first, then smaller tolerances (this prevents scratches on small tolerance surfaces and prevents part deformation). 2. Choose reasonable spindle speed, feed rate, and cutting depth based on material hardness. My personal summary is as follows: 1. For carbon steel materials, choose high speed, high feed rate, and large cutting depth. For example: 1Gr11, choose S1600, F0.2, cutting depth 2mm. 2. For hard alloys, choose low speed, low feed rate, and small cutting depth. For example: GH4033, choose S800, F0.08, cutting depth 0.5mm. 3. For titanium alloys, choose low speed, high feed rate, and small cutting depth. For example: Ti6, choose S400, F0.2, cutting depth 0.3mm. Tool Setting Skills Tool setting can be divided into tool setting with a tool setter and direct tool setting. Most lathes do not have a tool setter, so direct tool setting is used. The following tool setting skills refer to direct tool setting. First, select the center of the right end face of the part as the tool setting point and set it as the zero point. After the machine returns to the origin, each tool that needs to be used is set to the zero point based on the center of the right end face of the part; when the tool touches the right end face, input Z0 and click measure. The tool compensation value will automatically record the measured value, indicating that the Z-axis tool setting is correct. The X tool setting is done by trial cutting; use the tool to turn the outer circle of the part slightly, measure the value of the turned outer circle (e.g., x is 20mm), input x20, click measure, and the tool compensation value will automatically record the measured value, indicating that the X-axis is also set correctly. This method of tool setting ensures that even if the machine loses power and restarts, the tool setting values will not change, making it suitable for large-scale, long-term production of the same part, and there is no need to reset the tool when the lathe is turned off. Debugging Skills After programming the part and setting the tools, trial cutting and debugging are required. To prevent errors in the program and tool setting mistakes that could cause machine collisions, we should first perform a dry run simulation. In the machine's coordinate system, move the tool to the right by 2-3 times the total length of the part; then start the simulation processing. After the simulation is complete, confirm that the program and tool setting are correct before starting to process the part. After completing the first part, perform a self-check to confirm it is qualified, then have a dedicated inspector check it. Only after the dedicated inspection confirms it is qualified can we say that the debugging is complete. Completing Part Processing After the first trial cut is completed, batch production should begin. However, the qualification of the first part does not guarantee that the entire batch will be qualified, as different processing materials can cause tool wear. Softer materials result in less tool wear, while harder materials cause faster wear. Therefore, during processing, frequent measurements and inspections are necessary to timely increase or decrease the tool compensation values to ensure part qualification. In summary, the basic principles of processing are: first rough processing to remove excess material from the workpiece, then finish processing; avoid vibrations during processing; prevent thermal deformation of the workpiece during processing. There are many reasons for vibrations, which may be due to excessive load, resonance between the machine and workpiece, insufficient rigidity of the machine, or dull tools. We can reduce vibrations by the following methods: reduce lateral feed rate and cutting depth, check if the workpiece is securely clamped, increase or decrease the tool speed to reduce resonance, and check if it is necessary to replace the tool. Additionally, to operate CNC machines safely and prevent collisions, I have the following insights: It is often said that one cannot learn machine operation without experiencing collisions, which is a very wrong and harmful understanding. Machine collisions can greatly damage the precision of the machine, and the impact varies for different types of machines. Generally, the impact is greater for machines with lower rigidity. Once a collision occurs, the impact on the machine's precision is fatal. Therefore, for high-precision CNC lathes, collisions must be absolutely avoided. As long as the operator is careful and masters certain anti-collision methods, collisions can be completely prevented and avoided. The main causes of collisions are: 1. Incorrect input of tool diameter and length; 2. Incorrect input of workpiece dimensions and other related geometric dimensions, as well as incorrect initial positioning of the workpiece; 3. Incorrect setting of the machine's workpiece coordinate system, or changes in the machine's zero point during processing. Most collisions occur during rapid movement of the machine, and the harm caused by collisions at this time is also the greatest, so they must be absolutely avoided. Therefore, operators should pay special attention to the initial stage of program execution and when changing tools. If there is an error in program editing, or if the tool diameter and length are input incorrectly, collisions can easily occur. In the final stage of the program, if the sequence of retracting the CNC axis is incorrect, collisions may also occur. To avoid the aforementioned collisions, operators should fully utilize their senses to observe any abnormal movements of the machine, such as sparks, noise, unusual sounds, vibrations, or burning smells. If any abnormal situation is found, the program should be stopped immediately, and the machine can only continue working after the issue is resolved. In summary, mastering CNC machine operation skills is a gradual process and cannot be achieved overnight. It is based on mastering the basic operations of the machine, fundamental mechanical processing knowledge, and basic programming knowledge. CNC machine operation skills are not static; they require the operator to fully utilize their imagination and hands-on ability in an organic combination, representing innovative labor.

                                                                     CNC Turning Operator Skills

Programming Skills

1. Processing sequence of parts: drill holes first and then flatten the ends (this prevents material shrinkage during drilling); rough turning first, then finish turning (this ensures part accuracy); process parts with larger tolerances first and then those with smaller tolerances (this prevents scratches on small tolerance surfaces and prevents part deformation).

2. Choose reasonable spindle speed, feed rate, and cutting depth based on material hardness. My personal summary is as follows:

1. For carbon steel materials, choose high speed, high feed rate, and large cutting depth. For example: 1Gr11, choose S1600, F0.2, cutting depth 2mm.

2. For hard alloys, choose low speed, low feed rate, and small cutting depth. For example: GH4033, choose S800, F0.08, cutting depth 0.5mm.

3. For titanium alloys, choose low speed, high feed rate, and small cutting depth. For example: Ti6, choose S400, F0.2, cutting depth 0.3mm.

Tool Setting Skills

Tool setting can be divided into tool setting with a tool setter and direct tool setting. Most lathes do not have a tool setter, so direct tool setting is used. The following tool setting skills refer to direct tool setting. First, select the center of the right end face of the part as the tool setting point and set it as the zero point. After the machine returns to the origin, each tool needed will be set to the zero point based on the center of the right end face of the part; when the tool touches the right end face, input Z0 and click measure, the tool compensation value will automatically record the measured value, indicating that the Z-axis tool setting is correct. The X tool setting is done by trial cutting; use the tool to turn the outer circle of the part slightly, measure the turned outer circle value (e.g., x is 20mm), input x20, click measure, and the tool compensation value will automatically record the measured value, indicating that the X-axis is also set correctly. This method of tool setting ensures that even if the machine loses power and restarts, the tool setting values will not change, making it suitable for large-scale, long-term production of the same part, and there is no need to reset the tool when the lathe is turned off.

Debugging Skills

After programming the part and setting the tools, trial cutting and debugging are necessary. To prevent errors in the program and tool setting mistakes that could lead to machine collisions, we should first perform a dry run simulation. In the machine's coordinate system, move the tool to the right by 2-3 times the total length of the part; then start the simulation. After the simulation is complete, confirm that the program and tool setting are correct before starting to process the part. After completing the first part, conduct a self-inspection to confirm it is qualified, then have a dedicated inspector check it. Only after the dedicated inspection confirms it is qualified can we consider the debugging finished.

Completing Part Processing

After the first trial cut of the part is completed, batch production should begin. However, the qualification of the first part does not guarantee that the entire batch will be qualified, as different processing materials can cause tool wear. Softer materials result in less tool wear, while harder materials cause faster wear. Therefore, during processing, frequent measurements and inspections are necessary to timely adjust the tool compensation values to ensure the parts are qualified.

In summary, the basic principles of processing are: first rough machining to remove excess material from the workpiece, then finish machining; avoid vibrations during processing; prevent thermal deformation of the workpiece. There are many reasons for vibrations, such as excessive load, resonance between the machine and workpiece, insufficient rigidity of the machine, or dull tools. We can reduce vibrations by: reducing lateral feed rates and cutting depths, checking whether the workpiece is securely clamped, increasing or decreasing the tool speed to reduce resonance, and checking if it is necessary to replace the tool.

Additionally, to operate CNC machines safely and prevent collisions, I have the following insights:

I often hear others say that you cannot learn machine operation without colliding with the machine. This is a very wrong and harmful understanding. Machine collisions can greatly damage the precision of the machine, and the impact varies for different types of machines. Generally, the impact is greater for machines with low rigidity.

Once a collision occurs, the impact on the machine's precision is fatal. Therefore, for high-precision CNC lathes, collisions must be absolutely avoided. As long as the operator is careful and masters certain anti-collision methods, collisions can be completely prevented and avoided.

The main reasons for collisions are:

1. Incorrect input of tool diameter and length;

2. Incorrect input of workpiece dimensions and other related geometric dimensions, as well as incorrect initial positioning of the workpiece; 3. Incorrect setting of the machine's workpiece coordinate system, or the machine's zero point being reset during processing, causing changes. Most collisions occur during rapid movement of the machine, and the harm caused by collisions at this time is also the greatest, so they should be absolutely avoided.

Therefore, operators should pay special attention to the initial stages of program execution and when changing tools. If there is an error in program editing, or if the tool diameter and length are input incorrectly, collisions can easily occur. In the final stages of the program, if the sequence of retracting the CNC axis is incorrect, collisions may also occur. To avoid the aforementioned collisions, operators should fully utilize their senses while operating the machine, observing for any abnormal movements, sparks, noise, unusual sounds, vibrations, or burning smells.

If any abnormal situation is found, the program should be stopped immediately. The machine can only continue working after the issue is resolved. In summary, mastering CNC machine operation skills is a gradual process and cannot be achieved overnight. It is built on a foundation of basic machine operation, fundamental machining knowledge, and basic programming knowledge. CNC machine operation skills are not static; they require the operator to fully utilize their imagination and hands-on abilities, representing innovative labor.

TAG:


RELATED INFORMATION

ADD

Gengguantun Industrial Development Zone, Qingxian County, Hebei Province, China

WeChat applet

WeChat applet

Business License