Some details to pay attention to when processing shaft parts.
Release time:
2021-01-15
【Summary】Shaft parts are a common type of component, characterized by a rotating body, with a length generally greater than its diameter. They are widely used in various mechanical devices to support transmission components, transmit torque, and bear loads. The processing of shaft parts must follow certain rules, and this article will provide an understanding of the specific processing steps and some issues to pay attention to. 1. Basic Processing Route for Shaft Parts The main processed surfaces of shaft parts are the outer cylindrical surface and common special-shaped surfaces. Therefore, the most suitable processing methods should be selected according to various precision levels and surface roughness requirements. The basic processing routes can be summarized into four. First is the processing route from rough turning to semi-fine turning, and then to fine turning. This is the main process route chosen for the outer cylindrical processing of shaft parts made from commonly used materials; secondly, the route from rough turning to semi-fine turning, then to rough grinding, and finally to fine grinding is the best choice for parts made from ferrous metals that require high precision, low surface roughness, and hardening, as grinding is the ideal subsequent processing operation; the third route is from rough turning to semi-fine turning, then to fine turning, and diamond turning. This processing route is specifically used for non-ferrous metal materials, as non-ferrous metals have lower hardness and can easily clog the gaps between sand grains. Using grinding usually does not easily achieve the required surface roughness, so fine turning and diamond turning processes must be used; the last processing route is from rough turning to semi-fine turning, then to rough grinding, fine grinding, and finally finishing. This route is often used for ferrous metal parts that have been hardened and require high precision with low surface roughness values. 2. Pre-processing of Shaft Parts Before turning the outer circle of shaft parts, some preparatory procedures must be carried out, which is the pre-processing process of shaft parts. The most important preparatory procedure is straightening. Because the workpiece blank often bends and deforms during manufacturing, transportation, and storage, to ensure reliable clamping and uniform distribution of machining allowance, straightening is performed using various presses or straightening machines in a cold state. 3. Positioning Reference for Processing Shaft Parts First, the center hole of the workpiece is used as the positioning reference for processing. In the processing of shaft parts, the coaxiality of various outer cylindrical surfaces, conical holes, and threaded surfaces, as well as the perpendicularity of the end face to the rotating axis, are important manifestations of positional accuracy. These surfaces are generally designed based on the axis's centerline, using the center hole for positioning, in accordance with the principle of reference coincidence. The center hole is not only the positioning reference during turning but also serves as the positioning reference and inspection reference for other processing operations, adhering to the principle of unified reference. When using two center holes for positioning, it is also possible to maximize the processing of multiple outer circles and end faces in one clamping. Secondly, the outer circle and center hole are used as the positioning reference for processing. This method effectively overcomes the disadvantage of poor rigidity in center hole positioning, especially when processing heavier workpieces, as center hole positioning can lead to unstable clamping and cannot handle large cutting amounts. Using the outer circle and center hole as positioning references alleviates this issue. During rough processing, using the outer cylindrical surface of the shaft and one center hole as the positioning reference can withstand larger cutting torque, making it the most common positioning method for shaft parts. Third, the two outer cylindrical surfaces are used as the positioning reference for processing. When processing the inner hole of a hollow shaft, the center hole cannot be used as the positioning reference, so the two outer cylindrical surfaces of the shaft should be used as the positioning reference. When processing the spindle of a machine tool, the two supporting shaft necks are often used as the positioning reference, which can effectively ensure the coaxiality requirements of the conical hole relative to the supporting shaft necks, eliminating errors caused by non-coinciding references. Finally, a conical plug with a center hole is used as the positioning reference for processing. This method is the most common in the processing of the outer cylindrical surface of hollow shafts. 4. Clamping of Shaft Parts The processing of conical plugs and conical sleeve mandrels must have high processing accuracy. The center hole is not only the positioning reference for its own manufacturing but also the reference for the fine processing of the outer circle of the hollow shaft, and it must ensure high coaxiality between the conical surface of the conical plug or conical sleeve mandrel and the center hole. Therefore, when selecting clamping methods, care should be taken to minimize the number of installations of the conical plug to reduce the repeated installation error of the part. In actual production, once the conical plug is installed, it is generally not removed or replaced during the processing until completion.
Some details to pay attention to when processing shaft parts
Shaft parts are a common type of component, characterized by a rotating body, generally longer than its diameter, widely used in various mechanical devices to support transmission components, transmit torque, and bear loads. The processing of shaft parts must follow certain rules, and this article will provide an understanding of the specific processing steps and some issues to pay attention to.
1. Basic processing route for shaft parts
The main processed surfaces of shaft parts are the outer cylindrical surface and common special-shaped surfaces, so the most suitable processing methods should be selected according to various precision levels and surface roughness requirements. The basic processing routes can be summarized into four.
First is the processing route from rough turning to semi-fine turning, and then to fine turning, which is the main process route chosen for the outer cylindrical processing of shaft parts made from commonly used materials; second is the route from rough turning to semi-fine turning, then to rough grinding, and finally to fine grinding, which is the best choice for parts made from ferrous metals with high precision requirements, low surface roughness requirements, and needing hardening, as grinding is the ideal subsequent processing operation; the third route is from rough turning to semi-fine turning, then to fine turning, and diamond turning, specifically used for processing non-ferrous metal materials, as non-ferrous metals have lower hardness and can easily clog the gaps between sand grains, making it difficult to achieve the required surface roughness with grinding, thus fine turning and diamond turning processes must be used; the last processing route is from rough turning to semi-fine turning, then to rough grinding, fine grinding, and finally finishing, which is a commonly adopted processing route for ferrous metal materials that have been hardened and require high precision and low surface roughness.
2. Pre-processing of shaft parts
Before turning the outer circle of shaft parts, some preparatory procedures must be carried out, which is the pre-processing process of shaft parts. The most important preparatory procedure is straightening. Because the workpiece blank often undergoes bending deformation during manufacturing, transportation, and storage. To ensure reliable clamping and uniform distribution of machining allowance, straightening is performed using various presses or straightening machines in a cold state.
3. Positioning reference for processing shaft parts
First, the center hole of the workpiece is used as the positioning reference for processing. In the processing of shaft parts, the coaxiality of various outer cylindrical surfaces, conical holes, and threaded surfaces, as well as the perpendicularity of the end face to the rotating axis, are important manifestations of positional accuracy. These surfaces are generally designed based on the axis's centerline, using the center hole for positioning, in accordance with the principle of reference coincidence. The center hole is not only the positioning reference during turning but also serves as the positioning and inspection reference for other processing operations, adhering to the principle of reference unity. When using two center holes for positioning, it is also possible to maximize the processing of multiple outer circles and end faces in one clamping.
Second, the outer circle and center hole are used as the positioning reference for processing. This method effectively overcomes the disadvantage of poor rigidity in center hole positioning, especially when processing heavier workpieces, as center hole positioning can lead to unstable clamping and cannot handle large cutting amounts. Using the outer circle and center hole as positioning references alleviates this issue. During rough processing, using the outer cylindrical surface of the shaft and a center hole as positioning references can withstand larger cutting torque, making it the most common positioning method for shaft parts.
The third method is to use the two outer cylindrical surfaces as the positioning reference for processing. When processing the inner hole of a hollow shaft, the center hole cannot be used as the positioning reference, so the two outer cylindrical surfaces of the shaft should be used instead. When processing the spindle of a machine tool, the two supporting shaft necks are often used as positioning references, which can effectively ensure the coaxiality requirements of the conical hole relative to the supporting shaft necks, eliminating errors caused by non-coinciding references.
Finally, using a conical plug with a center hole as the positioning reference for processing. This method is the most commonly used in the processing of the outer cylindrical surface of hollow shafts.
4. Clamping of shaft parts
The processing of conical plugs and conical sleeve mandrels must have high processing accuracy, as their center holes are not only the positioning reference for their own manufacturing but also the reference for the fine processing of the outer circle of hollow shafts, ensuring high coaxiality between the conical surface of the conical plug or conical sleeve mandrel and the center hole. Therefore, when selecting clamping methods, care should be taken to minimize the number of installations of the conical plug to reduce the repeated installation errors of the parts. In actual production, once the conical plug is installed, it is generally not removed or replaced during the processing until completion.
TAG:
RELATED INFORMATION
FAX
ADD
Gengguantun Industrial Development Zone, Qingxian County, Hebei Province, China
WeChat applet