CNC machining knowledge


Release time:

2021-04-12

【Summary】1. Impact on cutting temperature: cutting speed, feed rate, back cutting amount Impact on cutting force: back cutting amount, feed rate, cutting speed Impact on tool durability: cutting speed, feed rate, back cutting amount 2. When the back cutting amount doubles, the cutting force doubles. When the feed rate doubles, the cutting force increases by about 70%. When the cutting speed doubles, the cutting force gradually decreases. In other words, if using G99, when the cutting speed increases, the cutting force will not change much. 3. The cutting force and cutting temperature can be judged based on the condition of the chips being discharged, whether they are within the normal range. 4. When the measured actual value X is greater than 0.8 compared to the diameter Y on the drawing while turning a concave arc, the tool with a secondary angle of 52 degrees (which is commonly used with a main angle of 35 degrees and a secondary angle of 93 degrees) may rub at the starting position of R. 5. The temperature represented by the color of the chips: white is less than 200 degrees. Yellow is 220-240 degrees. Dark blue is 290 degrees. Blue is 320-350 degrees. Purple-black is greater than 500 degrees. Red is greater than 800 degrees. 6. The default G commands in FUNAC OI mtc are generally: G69: not very clear. G21: metric size input. G25: spindle speed fluctuation detection off. G80: cancel fixed cycle. G54: default coordinate system. G18: ZX plane selection. G96 (G97): constant linear speed control. G99: feed per revolution. G40: cancel tool tip compensation (G41 G42). G22: storage stroke detection on. G67: cancel modal call of macro program. G64: not very clear. G13.1: cancel polar coordinate interpolation mode. 7. External threads are generally 1.3P, internal threads are 1.08P. 8. Thread speed S1200/pitch * safety factor (generally 0.8). 9. Manual tool tip R compensation formula: for chamfering from bottom to top: Z=R*(1-tan(a/2)) X=R(1-tan(a/2))*tan(a). For chamfering from top to bottom, change subtraction to addition. 10. For every increase of 0.05 in feed, the speed decreases by 50-80 revolutions. This is because reducing speed means less tool wear, and the increase in cutting force is slower, thus compensating for the increase in cutting force and temperature due to the increase in feed. 11. The impact of cutting speed and cutting force on the tool is crucial. Excessive cutting force is the main reason for tool breakage. The relationship between cutting speed and cutting force: as cutting speed increases with constant feed, cutting force gradually decreases. However, higher cutting speeds will lead to faster tool wear, increasing cutting force and temperature. When cutting force and internal stress become too great for the blade to withstand, it will break (of course, this also includes stress and hardness reduction caused by temperature changes). 12. When processing on a CNC lathe, the following points should be particularly noted: 1) Currently, the economic CNC lathes in China generally use ordinary three-phase asynchronous motors to achieve stepless speed regulation through inverters. If there is no mechanical reduction, the spindle output torque is often insufficient at low speeds. If the cutting load is too great, it is easy to stall, but some machines with gear positions solve this problem well. 2) Try to ensure that the tool can complete the processing of a part or a work shift. Special attention should be paid to avoid changing tools midway during the finishing of large parts to ensure that the tool can complete the processing in one go. 3) When turning threads with a CNC lathe, try to use a higher speed to achieve high-quality, efficient production. 4) Try to use G96. 5) The basic concept of high-speed processing is to make the feed exceed the heat conduction speed, thus discharging cutting heat with the chips and isolating the cutting heat from the workpiece, ensuring that the workpiece does not heat up or heats up less. Therefore, high-speed processing selects a very high cutting speed matched with high feed while selecting a smaller back cutting amount. 6) Pay attention to the compensation of the tool tip R. 13. Workpiece material cutting process classification table (small P79). Common thread cutting times and back cutting amount table (large P587). Common geometric shape calculation formulas (large P42). Inch to millimeter conversion table (large P27). 14. When turning grooves, vibrations and tool breakage often occur. The root cause of all this is the increase in cutting force and insufficient tool rigidity. The shorter the tool extension length, the smaller the back angle, and the larger the blade area, the better the rigidity, allowing it to withstand larger cutting forces. However, the wider the groove tool, the greater the cutting force it can withstand, but its cutting force will also increase. Conversely, a smaller groove tool can withstand less force, but its cutting force is also smaller. 15. Causes of vibration when turning grooves: 1) The tool extension length is too long, resulting in reduced rigidity. 2) The feed rate is too slow, resulting in increased unit cutting force, causing significant vibrations. The formula is: P=F/back cutting amount*f, where P is the unit cutting force and F is the cutting force. Additionally, excessive spindle speed can also cause vibrations. 3) Insufficient machine rigidity, meaning the tool can withstand cutting force, but the machine cannot. In simple terms, the machine cannot move. Generally, new machines do not have this problem; machines with this problem are either very old or frequently encounter machine killers. 16. When processing a batch, the dimensions may seem fine at first, but after a few hours, the dimensions change and become unstable. The reason may be that at the beginning, the tools are new, so the cutting force is not very large. However, after a period of time, the tool wears out, the cutting force increases, causing the workpiece to shift in the chuck, resulting in unstable dimensions. 17. When using G71, the values of P and Q cannot exceed the total sequence number of the program; otherwise, an alarm will occur: G71-G73 command format is incorrect, at least in FUANC. 18. In the FANUC system, there are two formats for subprograms: 1) P000 0000, the first three digits indicate the number of loops, and the last four digits indicate the program number. 2) P0000L000, the first four digits indicate the program number, and the three digits after L indicate the number of loops. 19. If the starting point of the arc remains unchanged, and the endpoint is offset by a mm in the Z direction, then the bottom diameter position of the arc is offset by a/2. 20. When drilling deep holes, do not grind the cutting grooves of the drill bit to facilitate chip removal. 21. If using a tool holder for drilling, the drill bit can be rotated to change the diameter of the hole. 22. When drilling center holes in stainless steel or drilling holes in stainless steel, the drill bit or center drill must be small; otherwise, it will not drill. When using cobalt drills, do not grind the grooves to avoid annealing during the drilling process. 23. According to the process, the blanking is generally divided into three types: one material at a time, two materials at a time, and the entire bar at once. 24. When turning threads, if an oval shape appears, it may be due to the material being loose. Just make a few more passes with the thread cutter. 25. In some systems that allow macro programs to be input, macro programs can replace subprogram loops, saving program numbers and avoiding many troubles. 26. If using a drill bit for reaming, but the hole has significant runout, a flat-bottom drill can be used for reaming, but the twist drill must be short to increase rigidity. 27. If directly using a drill bit to drill holes on a drilling machine, the hole diameter may deviate. However, if reaming on a drilling machine, the size generally will not deviate. For example, using a 10MM drill bit for reaming on a drilling machine, the resulting hole diameter generally has a tolerance of about 3 wires. 28. When turning small holes (through holes), try to ensure that the chips are continuously rolled and discharged from the tail. Key points for rolling chips: 1. The position of the tool should be appropriately raised. 2. Appropriate cutting edge inclination angle, back cutting amount, and feed rate. Remember, the tool should not be too low; otherwise, it is easy to break the chips. If the secondary angle of the tool is large, even if the chips break, they will not jam the tool holder. If the secondary angle is too small, the broken chips will jam the tool holder, which can be dangerous. 29. The larger the cross-section of the tool holder in the hole, the less likely it is to vibrate. Additionally, a strong rubber band can be tied to the tool holder, as it can help absorb vibrations. 30. When turning copper holes, the R of the tool tip can be slightly larger (R0.4-R0.8), especially when turning a taper. Iron parts may not have much issue, but copper parts can easily jam the chips.

                                              CNC Machining Knowledge

1. The influence on cutting temperature: cutting speed, feed rate, back cutting amount
 
The influence on cutting force: back cutting amount, feed rate, cutting speed
 
The influence on tool durability: cutting speed, feed rate, back cutting amount
 
2. When the back cutting amount doubles, the cutting force doubles.
 
When the feed rate doubles, the cutting force increases by about 70%.
 
When the cutting speed doubles, the cutting force gradually decreases.
 
In other words, if using G99, when the cutting speed increases, the cutting force will not change much.
 
3. The cutting force and cutting temperature can be judged based on the condition of the chips being discharged.
 
4. When the actual measured value X is greater than 0.8 compared to the diameter Y on the drawing, the R produced by the tool with a secondary angle of 52 degrees (which is commonly used with a main angle of 35 degrees and a secondary angle of 93 degrees) may rub against the starting position.
 
5. The temperature represented by the color of the chips: white is less than 200 degrees.
 
Yellow is 220-240 degrees.
 
Dark blue is 290 degrees.
 
Blue is 320-350 degrees.
 
Purple-black is greater than 500 degrees.
 
Red is greater than 800 degrees.
 
6. FUNAC OI mtc generally defaults to G commands:
 
G69: Not very clear.
 
G21: Metric size input.
 
G25: Spindle speed fluctuation detection off.
 
G80: Cancel fixed cycle.
 
G54: Default coordinate system.
 
G18: ZX plane selection.
 
G96 (G97): Constant linear speed control.
 
G99: Feed per revolution.
 
G40: Cancel tool tip compensation (G41 G42).
 
G22: Store stroke detection on.
 
G67: Cancel macro program modal call.
 
G64: Not very clear.
 
G13.1: Cancel polar coordinate interpolation mode.
 
7. External threads are generally 1.3P, internal threads are 1.08P.
  
8. Thread speed S1200/pitch * safety factor (generally 0.8).
  
9. Manual tool tip R compensation formula: for chamfering from bottom to top: Z=R*(1-tan(a/2)) X=R(1-tan(a/2))*tan(a). For chamfering from top to bottom, change subtraction to addition.
  
10. For every 0.05 increase in feed, the speed decreases by 50-80 RPM. This is because reducing speed means slower tool wear, and the increase in cutting force compensates for the increase in cutting force and temperature due to the increase in feed.
 
11. The relationship between cutting speed and cutting force is crucial for tool performance. Excessive cutting force is a major reason for tool breakage. As cutting speed increases with constant feed, cutting force gradually decreases, but higher cutting speeds also lead to faster tool wear, increasing cutting force and temperature. When cutting force and internal stress exceed the tool's capacity, it will break (of course, this is also due to stress and hardness changes caused by temperature variations).
 
12. When machining with CNC lathes, the following points should be particularly noted:
 
1) Currently, CNC lathes in China generally use ordinary three-phase asynchronous motors with frequency converters for stepless speed regulation. Without mechanical reduction, the spindle often lacks sufficient torque at low speeds, making it easy to stall under heavy cutting loads. However, some machines are equipped with gear positions that effectively solve this problem.
 
2) Try to ensure that the tool can complete the machining of a part or a work shift. Special attention should be paid to avoid tool changes during the finishing of large parts to ensure that the tool can complete the machining in one go.
 
3) When turning threads with CNC lathes, try to use higher speeds to achieve high-quality, efficient production.
 
4) Try to use G96.
 
5) The basic concept of high-speed machining is to make the feed exceed the heat conduction speed, thus discharging cutting heat with the chips and isolating the cutting heat from the workpiece, ensuring that the workpiece does not heat up or heats up minimally. Therefore, high-speed machining selects a very high cutting speed matched with high feed while selecting a smaller back cutting amount.
 
6) Pay attention to the compensation of tool tip R.
 
13. Workpiece material cutting machinability grading table (Small P79).
 
Common thread cutting times and back cutting amount table (Large P587).
 
Common geometric calculation formulas (Large P42).
 
Inch to millimeter conversion table (Large P27).
  
14. When machining grooves, vibrations and tool breakage often occur. The root cause of all this is the increase in cutting force and insufficient tool rigidity. The shorter the tool extension length, the smaller the back angle, and the larger the area of the blade, the better the rigidity, allowing it to withstand larger cutting forces. However, the wider the groove tool, the greater the cutting force it can withstand, but its cutting force will also increase. Conversely, a smaller groove tool can withstand less force, but its cutting force will also be smaller.
 
15. Causes of vibration during groove machining:
 
1) The length of the tool extension is too long, resulting in reduced rigidity.
 
2) The feed rate is too slow, resulting in an increase in unit cutting force, which causes significant vibration. The formula is: P=F/back cutting amount*f, where P is the unit cutting force and F is the cutting force. Additionally, if the spindle speed is too fast, it can also cause vibration.
 
3) The rigidity of the machine tool is insufficient, meaning the tool can withstand cutting force, but the machine tool cannot. In simple terms, the machine tool cannot move. Generally, new machines do not have this kind of problem; machines with this issue are either very old or frequently encounter machine killers.
 
16) When machining a part, at first, the dimensions are fine, but after a few hours, the dimensions change and become unstable. The reason may be that at the beginning, the tools are new, so the cutting force is not very large. However, after a period of machining, the tool wears out, the cutting force increases, causing the workpiece to shift in the chuck, resulting in dimensions that are consistently off and unstable.
 
17) When using G71, the values of P and Q cannot exceed the total sequence number of the program; otherwise, an alarm will occur: G71-G73 command format is incorrect, at least in FANUC.
  
18) There are two formats for subprograms in the FANUC system:
 
1) P000 0000, the first three digits indicate the number of cycles, and the last four digits indicate the program number.
 
2) P0000L000, the first four digits indicate the program number, and the three digits after L indicate the number of cycles.
  
19) If the starting point of the arc remains unchanged, and the endpoint shifts a mm in the Z direction, then the position of the arc's bottom diameter shifts by a/2.
  
20) When drilling deep holes, the drill bit should not have cutting grooves to facilitate chip removal.
  
21) If using a tool holder to drill holes, the drill bit can be rotated to change the diameter of the hole.
  
22) When drilling a center hole in stainless steel or drilling a hole in stainless steel, the drill bit or center drill must be small; otherwise, it cannot be drilled. When using a cobalt drill to drill holes, do not grind the grooves to avoid annealing the drill bit during the drilling process.
  
23) According to the process, the material is generally divided into three types: one material at a time, two materials at a time, and the entire bar material at once.
  
24) When threading, if an oval shape appears, it may be due to the material being loose. Just use a threading tool to make a few more passes.
  
25) In some systems that allow macro programs to be input, macro programming can replace subprogram loops, saving program numbers and avoiding many troubles.
  
26) If using a drill bit to enlarge a hole, but the runout is large, a flat-bottom drill can be used to enlarge the hole, but the twist drill must be short to increase rigidity.
  
27) If directly using a drill bit to drill holes on a drilling machine, the hole diameter may deviate. However, if enlarging the hole on the drilling machine, the size generally will not deviate. For example, if using a 10MM drill bit to enlarge a hole on the drilling machine, the resulting hole diameter is generally within a tolerance of about 3 thousandths.
  
28) When machining small holes (through holes), try to ensure that the chips are continuously rolled and then discharged from the tail end. Key points for chip rolling: 1. The position of the tool should be appropriately raised; 2. Appropriate cutting edge angle, cutting amount, and feed rate. Remember, the tool should not be too low; otherwise, it is easy to break the chips. If the tool's secondary angle is large, even if the chips break, they will not jam the tool holder. If the secondary angle is too small, the broken chips will jam the tool holder, which can be dangerous.
  
29) The larger the cross-section of the tool holder in the hole, the less likely it is to vibrate. Additionally, a strong rubber band can be tied to the tool holder, as it can help absorb vibrations.
  
30) When machining copper holes, the tip radius of the tool can be slightly larger (R0.4-R0.8), especially when machining a taper. Iron parts may not have much issue, but copper parts can easily jam chips.

TAG:


RELATED INFORMATION

ADD

Gengguantun Industrial Development Zone, Qingxian County, Hebei Province, China

WeChat applet

WeChat applet

Business License