Aluminum alloy drilling methods
Release time:
2021-06-17
【Summary】Aluminum and its alloys, due to their low density and certain mechanical properties, as well as good electrical conductivity, thermal conductivity, and corrosion resistance, are widely used in various industrial sectors, especially in the aviation field. However, there are many processing difficulties in drilling aluminum alloys. Aluminum alloys are divided into two main categories based on the manufacturing method: cast and deformed (which can be rolled). Deformed aluminum alloys are mostly used to manufacture stretched parts, rivets, sheets, profiles, etc. In this category of parts, drilling is not common during processing, so we will not consider it for now. On the other hand, cast aluminum alloys have many varieties, with the most basic being aluminum-silicon alloys. Methods for drilling aluminum alloys Compared to steel and brass, the characteristics of aluminum alloys are: 1. The material is soft and has poor rigidity. 2. The elastic modulus is low. These two factors significantly affect the machinability of aluminum alloys. Therefore, when processing aluminum alloy workpieces, it is essential to clamp and support the workpiece adequately and keep the cutting tool sharp. Otherwise, the workpiece often tends to move away from the cutting tool. Sometimes, the surface of the workpiece shows irregular grooves and shiny extrusion marks, which may be caused by abnormal pressure from the tool on the workpiece, or it may be due to insufficient clamping leading to vibration, causing the tool to rub against the surface of the workpiece, resulting in extrusion phenomena and powdery cutting. When the gap or elasticity disappears, the tool bites into the surface of the workpiece, creating grooves. Therefore, during the drilling process, we must also pay attention to the key points of cutting aluminum alloys and reasonably select the cutting methods for aluminum alloys. Choosing aluminum alloy group drills In the drilling process, standard group drills have relatively large outer edge cutting angles (2Φ) and inner edge cutting angles (2Φ''''), with a smaller back angle (α). The friction between the back face and the machined surface is severe, generating a lot of cutting heat, and the cutting temperature rises quickly. The entry angle of the main cutting edge into the material is small, making the cutting thickness thin, which is prone to breakage and difficult to discharge. The front angle of the inner edge is negative, which means it is entirely in a state of extrusion cutting during work, leading to high local temperatures and severe material melting. Improvements in the geometric parameters and shape of aluminum alloy special group drills. After long-term practice, we have improved the geometric parameters and shape of standard group drills, grinding them into special drill bits for aluminum alloys. The original 140° outer edge cutting angle has been reduced to 105°–110°, which reduces axial force, increases the tip angle, improves heat dissipation conditions, and intensifies chip deformation, forming strip-shaped chips. Increasing the back angle, the back angle α has been increased from the original 13°–14° to 22°–23°, which reduces the generation of cutting heat, alleviates the melting phenomenon, and the larger back angle also makes the main cutting edge sharper, making it easier to cut into the material and form thick chips for easy discharge. Changing the original inner edge front angle of about -10° to a positive value or close to a positive value can significantly reduce cutting resistance and improve the cutting state of the inner edge. Changing the original double-sided arc groove to a single-sided arc groove can effectively reduce cutting resistance and increase chip thickness without causing vibration under the condition of low hardness of aluminum alloys. Grinding more of the edge along the back side of the horizontal edge to increase the chip space. 2) Grinding methods for aluminum alloy group drills. Prepare to use A46–60K, L model grinding wheels, ensuring the grinding wheel is flat, and the outer edge of the grinding wheel should not exceed the arc radius of the drill bit. When grinding straight edges, align the cutting edge of the drill bit with the flat surface of the grinding wheel, and the drill bit axis should be angled to the left at the peak angle of the chip. Grind from the cutting edge to the back face, swinging the drill bit handle up and down, ensuring that the hand has a support point throughout the process, and the tail of the drill bit should not rise above the horizontal plane. When grinding crescent grooves, the main cutting edge of the drill bit should contact the edge of the grinding wheel, and the cutting edge should not be raised. Press the handle of the drill bit down to grind the back face, maintaining a 55° angle between the grinding wheel and the drill axis, keeping the drill bit level without up and down swinging. For the horizontal edge, tilt the drill bit axis to the left by 15°, and press down the tail of the drill bit by 55°, forming an angle between the outer edge and the side of the grinding wheel. Ensure timely cooling of the drill bit to avoid annealing of the drill core. Finally, deepen the inner groove of the drill bit using a flat grinding wheel or small grinding wheel, paying attention to the angle of the back angle to avoid the back face space being higher than the arc cutting edge. Polishing the cutting edge To reduce the occurrence of built-up edge, especially to avoid residual marks from built-up edge when it disappears, the front face (spiral groove) and back face of the drill bit should be polished to above 0.8μm with an oil stone; it is best to choose drill bits with polished flutes. Choosing appropriate cutting parameters The ultimate speed and high feed rate are the cutting objectives when drilling aluminum alloys. High speed can provide greater centrifugal force, making it easier for chips to be ejected in a jet-like manner from the spiral groove, while also shortening the unit residence time of chips on the cutting edge, reducing the possibility of adhesion. A larger feed rate can reduce the cutting heat generated within the unit cutting volume. Adequately clamping and supporting the workpiece When processing aluminum alloy workpieces, it is essential to clamp and support the workpiece adequately and keep the cutting tool sharp. Otherwise, the workpiece often tends to move away from the cutting tool. Sometimes, the surface of the workpiece shows irregular grooves and shiny extrusion marks, which may be caused by abnormal pressure from the tool on the workpiece, or it may be due to insufficient clamping leading to vibration, causing the tool to rub against the surface of the workpiece, resulting in extrusion phenomena and powdery cutting. When the gap or elasticity disappears, the tool bites into the surface of the workpiece, creating grooves. Selecting a reasonable processing process To obtain a smooth surface on the workpiece, it is advisable to use a combination of drilling followed by reaming, as various qualified aluminum alloy workpiece blanks will always have some oxide layers, which exacerbate the wear of the drill bit. Choosing compatible cutting fluids The choice of cutting fluid for aluminum alloys is very important, as it must ensure good lubrication, cooling, filtration, and rust prevention. Therefore, cutting fluids suitable for aluminum alloy processing differ from ordinary cutting fluids. During drilling, due to high-speed processing, a large amount of heat can be generated. If the heat generated cannot be promptly carried away by the cutting fluid, it will lead to tool adhesion, and in severe cases, built-up edge will occur, which will severely affect the processing roughness of the workpiece and the service life of the tool. Additionally, heat can cause deformation of the workpiece, severely affecting its precision. Therefore, when selecting cutting fluids, both the lubrication properties and cooling performance must be considered. For finishing, it is advisable to choose emulsified anti-friction cutting fluids or low-viscosity cutting oils; for semi-finishing and rough machining, low-concentration emulsified anti-friction cutting fluids or semi-synthetic anti-friction cutting fluids with good cooling performance can be selected.
Aluminum Alloy Drilling Methods
On the other hand, cast aluminum alloys have many varieties, the most basic being aluminum-silicon alloys.
Methods for drilling aluminum alloys
TAG:
RELATED INFORMATION
FAX
ADD
Gengguantun Industrial Development Zone, Qingxian County, Hebei Province, China
WeChat applet