Diagnosis and Maintenance of the 5 Core Issues of Lathe Tool Holders
Release time:
2021-10-06
【Summary】Diagnosis and Maintenance of 5 Major Core Issues of Lathe Tool Holders CNC tool holders are the most common auxiliary devices for CNC lathes. They allow CNC lathes to complete multiple or even all processing procedures in one clamping of the workpiece, thereby shortening auxiliary processing time and reducing errors caused by multiple installations of the workpiece during processing, thus improving the processing efficiency and accuracy of the machine tool. Engineers from Repair Bar will share their years of maintenance experience regarding tool holder fault diagnosis and maintenance. 1. Tool holder cannot start 1) Mechanical reasons The pre-tightening force of the tool holder is too large. When a fixed wrench is inserted into the end of the worm and rotated, it is difficult to turn, but it can be turned with force. However, after the next clamping, the tool holder still cannot start. If this phenomenon occurs, it can be determined that the reason for the tool holder not starting is that the pre-tightening force is too large, which can be eliminated by reducing the clamping current of the tool holder motor. The internal mechanism of the holder is jammed. When rotating the worm from the end of the worm, it cannot be turned clockwise, which is due to mechanical jamming. First, check whether the anti-back positioning pin of the clamping device is in the anti-back ratchet groove. If it is, the anti-back ratchet and screw connection pin hole need to be rotated at an angle to re-drill and connect; secondly, check whether the spindle nut is locked. If the nut is locked, it should be readjusted; again, if the rotating parts are jammed due to poor lubrication, they should be disassembled, observed, and lubricated. 2) Electrical reasons Power supply is not connected, motor does not turn. Check whether the fuse is intact, whether the power switch is well connected, and whether the switch position is correct. When measuring the voltage with a multimeter, check whether the voltage value is within the specified range. This can be eliminated by replacing the fuse, adjusting the switch position, and ensuring good contact at the connection points. In addition, the reason for the power supply not being connected may also consider the broken cable between the tool holder and the controller, internal broken wires in the tool holder, or changes in the position of the brush-type Hall element leading to abnormal on-off. The forward input terminal and reverse input terminal of the inverter are disconnected. Normal tool change, machine control does not change tools, focus on checking the lead between the counting machine and the tool holder controller, the computer I/O interface, and the tool holder position response signal. In the ladder diagram, the forward output signal Y0.0 and reverse output signal Y0.1 are low level when there is an input signal, leading to the corresponding relay not outputting. 2. A certain tool number of the tool holder keeps turning, while other tool positions can rotate 1. The Hall element of this tool position is damaged. Confirm which tool position causes the tool holder to keep turning. Input instructions on the system to rotate this tool position and use a multimeter to measure whether there is a voltage change at the signal contact of this tool position against the 24V contact. If there is no change, it can be determined that the Hall element of this tool position is damaged, and the signal disk or Hall element can be replaced. 2. The signal line of this tool position is open, causing the system to be unable to detect the tool position signal. Check whether the signal of this tool position and the system's connection has an open circuit, and reconnect it correctly. 3. There is a problem with the tool position signal receiving circuit of the system. If it is confirmed that the Hall element of this tool position is fine and the signal connection with the system is also fine, replace the main board. 3. The tool holder does not lock tightly 1. The position of the signal disk is not aligned. Open the top cover of the tool holder, rotate and adjust the position of the signal disk so that the Hall element of the tool holder aligns with the magnetic steel, making the tool position stop at the correct position. 2. The system's anti-lock time is not long enough. Adjust the system's anti-lock time parameter (the anti-lock time t for the new tool holder is 1.2s). 3. Mechanical locking mechanism failure. Disassemble the tool holder, adjust the mechanism, and check whether the positioning pin is broken. 4. The tool holder runs continuously and does not stop at the position 1. Since the tool holder can run continuously, the possibility of mechanical failure is small, mainly check from the electrical aspect. 2. Check whether the position signal is sent. If there is no position signal, it is a fault of the signal disk. 3. Check whether the elastic contact of the signal disk is worn out, whether the ground wire of the signal disk is open, whether there is poor contact or disconnection. At this time, it is necessary to replace the elastic contact or repair it, and conduct corresponding troubleshooting based on the contact situation of the relay in the circuit, the contact situation of the position switch, and the connection situation of the circuit. 5. The tool holder overshoots or does not reach the position 1. Tool holder overshoot. The mechanical reason for this fault is likely large, mainly due to the failure of the backstop device. ① First, check whether the backstop positioning pin is flexible and whether the spring is fatigued. At this time, the positioning pin should be repaired to make it flexible or replace the spring. ② Secondly, check whether the backstop ratchet is disconnected from the worm. If disconnected, the connecting pin needs to be replaced. ③ If the overshoot phenomenon still occurs, it may be due to the tool being too long and heavy, and the elastic modulus of the positioning pin spring should be replaced with a slightly larger one. 2. The tool holder does not reach the position (sometimes suddenly stops at an intermediate position). This fault is mainly due to the misalignment of the signal disk contact and the elastic contact, that is, the fixed offset of the tool position signal rubber disk. ① First, readjust the position of the signal disk and the elastic contact and fix it securely. ② If the fault cannot be eliminated, it may be due to the loosening of the clamping nut of the signal disk, causing the position to shift. 6. Inputting the tool number can rotate the tool holder, but directly pressing the tool change button cannot rotate the tool holder 1. The Hall element is deviated from the magnetic block, placed in front of the magnetic block. When manually pressing the tool change button, the tool holder just starts to rotate and detects the tool holder position signal, then immediately reverses the tool holder. At this time, check whether the Hall element on the tool holder signal disk is deviated from the position, and adjust the position of the signal disk to align the Hall element with the magnetic block. 2. The manual tool change button is malfunctioning, and it can be directly replaced. 7. The tool number of the tool is not the same as the tool number displayed in the lathe system 1. This situation generally occurs after the maintenance of the tool holder, leading to new problems caused by the maintenance. One possibility is that the position of the magnetic block is incorrect; another possibility is a connection problem in the tool holder's internal circuit. 2. Some tool holders have magnetic blocks in the upper cover of the tool holder. At this time, the position of the upper cover after repair cannot be installed randomly. Generally, marks should be made for the installation before repair, and of course, the position of the upper cover can be changed after repair to find its correct position. 3. Tool holder circuit problems generally cannot be solved by simply changing the position of the magnetic block. Now, only the position of the wiring head can be changed. As a maintainer, it is essential to pay attention to the correct position of each wiring head inside the tool holder before maintenance. Some maintainers think that seeing the instructions printed inside the tool holder is enough to clarify the wiring order of each line, but this is not sufficient. In addition to the order, attention should also be paid to which terminal the joint is connected to. Generally, when knowing the order of each line, the corresponding two wire ends should be marked using methods such as wire clips. Based on the above analysis of causes, inspection methods, and solutions, it helps to find the fault causes in a timely and effective manner and quickly eliminate faults. Economic CNC lathes are commonly used machine tools. In the maintenance process, it is not only important to repair well but also to repair quickly. To do a good job in machine tool maintenance, it is not only about mastering theory but also about continuously summarizing and improving in practice to accumulate rich maintenance experience, so as to efficiently carry out maintenance on CNC lathe tool holders.
5 Major Core Issues of Lathe Tool Holder Fault Diagnosis and Maintenance
The CNC tool holder is the most common auxiliary device for CNC lathes. It allows the CNC lathe to complete multiple or even all processing procedures in one clamping of the workpiece, thereby shortening auxiliary processing time and reducing errors caused by multiple installations of the workpiece during processing, thus improving the processing efficiency and accuracy of the machine tool. Engineers from Repair Bar will share their years of maintenance experience regarding tool holder fault diagnosis and repair.
1. Tool holder cannot start
1) Mechanical reasons
The pre-tightening force of the tool holder is too large. When a fixed wrench is inserted into the end of the worm and rotated, it is difficult to turn, but it can be turned with force. However, after the next clamping, the tool holder still cannot start. If this phenomenon occurs, it can be determined that the reason for the tool holder not starting is that the pre-tightening force is too large, which can be eliminated by reducing the clamping current of the tool holder motor.
The internal mechanism of the holder is jammed. When rotating the worm from the end, it cannot turn clockwise, which is caused by mechanical jamming. First, check whether the anti-back positioning pin of the clamping device is in the anti-back ratchet groove. If it is, the anti-back ratchet and the screw connecting pin hole need to be rotated at an angle to re-drill and connect; second, check whether the spindle nut is locked. If the nut is locked, it should be readjusted; third, if the rotating parts are jammed due to poor lubrication, it should be disassembled, observed, and lubricated.
2) Electrical reasons
Power is not connected, and the motor does not turn. Check whether the fuse is intact, whether the power switch is well connected, and whether the switch position is correct. When measuring the voltage with a multimeter, check if the voltage value is within the specified range. This can be eliminated by replacing the fuse, adjusting the switch position, and ensuring good contact at the connection points. In addition, the reason for the power not being connected may also consider the broken cable between the tool holder and the controller, internal wire breakage of the tool holder, or changes in the position of the brush-type Hall element leading to abnormal on-off.
The forward input terminal and reverse input terminal of the inverter are disconnected.
The tool change is normal, but the machine control does not change tools. Focus on checking the lead between the counting machine and the tool holder controller, the computer I/O interface, and the tool holder position response signal.
In the ladder diagram, the forward output signal Y0.0 and reverse output signal Y0.1 are low level when there is an input signal, causing the corresponding relay to have no output.
2. A certain tool number of the tool holder keeps rotating, while other tool positions can rotate.
1. The Hall element of this tool position is damaged. Confirm which tool position causes the tool holder to keep rotating. Input the command on the system to rotate that tool position and use a multimeter to measure whether there is a voltage change at the signal contact of that tool position against the 24V contact. If there is no change, it can be determined that the Hall element of that tool position is damaged, and the signal disc or Hall element can be replaced.
2. The signal line of this tool position is broken, causing the system to be unable to detect the tool position signal. Check whether the signal line of this tool position is broken and reconnect it correctly.
3. There is a problem with the tool position signal receiving circuit of the system. If it is confirmed that the Hall element of that tool position is fine and the signal line of that tool position to the system is also fine, replace the mainboard.
3. The tool holder cannot lock tightly.
1. The position of the signal disc is not aligned. Open the top cover of the tool holder, rotate and adjust the position of the signal disc so that the Hall element of the tool holder aligns with the magnetic steel, allowing the tool position to stop at the correct position.
2. The system's anti-lock time is not long enough. Adjust the system's anti-lock time parameter (the anti-lock time t for the new tool holder should be 1.2s).
3. Mechanical locking mechanism failure. Disassemble the tool holder, adjust the mechanism, and check whether the positioning pin is broken.
4. The tool holder runs continuously and does not stop at the position.
1. Since the tool holder can run continuously, the possibility of mechanical failure is small, mainly check from the electrical aspect.
2. Check whether the position signal is sent. If there is no position signal, it is a fault of the signal disc.
3. Check whether the elastic contact of the signal disc is worn out, whether the ground wire of the signal disc is broken, whether there is poor contact or missed connection. At this time, it is necessary to replace the elastic contact or repair it, and conduct corresponding troubleshooting based on the contact conditions of the relays in the circuit, the contact conditions of the position switch, and the connection conditions of the circuit.
5. The tool holder overshoots or does not reach the position.
1. The tool holder overshoots. The mechanical cause of this fault is likely large, mainly due to the failure of the backstop device.
① First, check whether the backstop positioning pin is flexible and whether the spring is fatigued. At this time, the positioning pin should be repaired to make it flexible or replace the spring.
② Second, check whether the backstop ratchet is disconnected from the worm. If disconnected, the connecting pin needs to be replaced.
③ If the overshoot phenomenon still occurs, it may be due to the tool being too long and heavy, and the elastic modulus of the positioning pin spring should be replaced with a slightly larger one.
2. The tool holder does not reach the position (sometimes it suddenly stops at an intermediate position). This fault is mainly due to the misalignment of the signal contacts of the signal disc and the elastic contact, that is, the fixed offset of the position of the signal rubber disc.
① First, readjust the position of the signal disc and the elastic contact and fix it securely.
② If the fault cannot be eliminated, it may be due to the loosening of the clamping nut of the signal disc, causing the position to shift.
6. Inputting the tool number can rotate the tool holder, but directly pressing the tool change button does not rotate the tool holder.
1. The Hall element is deviated from the magnetic block, placed in front of the magnetic block. When manually pressing the tool change button, the tool holder detects the position signal as soon as it starts to rotate, and then immediately reverses the tool holder. At this time, check whether the Hall element on the tool holder signal disc is out of position, and adjust the position of the signal disc to align the Hall element with the magnetic block.
2. The manual tool change button is malfunctioning. In this case, the manual tool change button can be directly replaced.
7. The tool number of the tool is not the same as the tool number displayed in the lathe system.
1. This situation generally occurs after the tool holder has been repaired, resulting in new issues caused by the maintenance. One possibility is that the position of the magnetic block is incorrect; another possibility is a connection issue within the tool holder's circuit.
2. Some magnetic blocks of the tool holder are located in the upper cover of the tool holder. At this time, the position of the upper cover after repair cannot be installed randomly. Generally, marks should be made for the installation at the back before repair, and of course, the position of the upper cover can also be changed after maintenance to find its correct position.
3. Circuit issues in the tool holder generally cannot be resolved by simply changing the position of the magnetic block. Currently, only the position of the wiring terminals can be changed. As a maintainer, it is essential to pay attention to the correct position of each wiring terminal inside the tool holder before maintenance. Some maintainers believe that understanding the instructions printed inside the tool holder and clarifying the wiring sequence is sufficient, but this is not enough. In addition to the sequence, attention must also be paid to which terminal each connector is attached to. Generally, when the sequence of wires is known, corresponding wire ends should be marked using methods such as wire clips.
Based on the above analysis of causes, inspection methods, and solutions, it helps to promptly and effectively identify the cause of the fault and quickly eliminate it. Economical CNC lathes are commonly used machine tools, and during maintenance, it is important not only to repair well but also to repair quickly. To perform well in machine tool maintenance, it is not only necessary to master the theory but also crucial to continuously summarize and improve in practice to accumulate rich maintenance experience, thus enabling efficient maintenance of the CNC lathe tool holder.
TAG:
RELATED INFORMATION
FAX
ADD
Gengguantun Industrial Development Zone, Qingxian County, Hebei Province, China
WeChat applet